THE INSTALLATION GUIDE

A clean finish.
One step at a time.

Everything you need to apply your cut-vinyl decal, from the first wipe to the final peel.

Dry applicationCut-vinyl decalsSmall details included

Our video walkthrough is coming soon. The complete written guide is below.

Clean. Rinse. Dry.

Wash away dirt and road grime with mild soap and water, then rinse thoroughly. On glass or a compatible, fully cured finish, wipe with isopropyl alcohol and a fresh lint-free cloth to remove remaining residue. Check the surface manufacturer’s cleaning advice first. Avoid wax, polish and residue-leaving glass cleaners. Let the surface dry completely, including edges and seams.

Tip Work in the shade on a cool surface. Aim for 15–25°C (59–77°F), away from wind, dust and direct sunlight.

Press the design onto the tape.

Lay the decal flat with the clear transfer tape facing up. Use a squeegee or a card wrapped in a soft cloth to press firmly across the entire design, paying attention to small letters and details. This helps the vinyl lift cleanly from its paper backing.

Tip Your decal has three layers: clear transfer tape, the cut vinyl design, and paper backing. Only the vinyl stays on your surface.

Line it up before peeling.

Keep the backing attached while you check placement. Measure from a reliable edge, then hold the decal in position with masking tape. For a small decal, tape across the top edge to make a hinge. For a wider design, use a centre hinge and apply one half at a time.

Tip Stand back and check the alignment. Leave room around seals, trim, wipers, sensors and your field of view.

Peel away the paper backing.

Lift the decal on its tape hinge and slowly peel the backing back on itself, keeping the transfer tape and vinyl together. If a detail stays on the paper, lower the backing, press that area again and retry slowly. Keep fingers away from the adhesive, and do not let the exposed design fold onto itself.

Tip Pull the paper away from the design rather than tugging the vinyl up from the paper.

Apply with overlapping strokes.

Hold the exposed decal slightly away from the surface. Starting at the hinge, gradually lower it while pressing across the transfer tape with a squeegee. Work from the centre toward the edges in overlapping strokes. Keep light control of the tape without stretching the vinyl, then make another firm pass over the full design.

Tip For a centre hinge, finish the first half, remove the masking tape, then repeat with the remaining backing and second half.

Peel the tape back slowly.

Give the adhesive a few minutes to grip. Peel the transfer tape slowly back over itself, close to the surface, rather than pulling outward. If a letter lifts, stop, lower the tape and press that area again. Once the tape is off, gently press down the edges with a clean, soft cloth.

Tip Do not rush tiny details. If a section keeps lifting, give it more time and check that the surface is clean and dry.

Give it time to settle.

Keep the decal dry for the first 48 hours. Avoid washing, scrubbing or running a wiper over it while the adhesive settles. After that, clean gently with mild soap and water. Keep pressure-washer jets, ice scrapers and abrasive brushes away from the edges.

A few small bubbles?

Some small bubbles relax over time. Do not pick at the vinyl or use a blade on the installed design. If a large bubble, lifted edge or stubborn detail concerns you, send us a photo before trying to fix it.

Ask us for help

A few things depend on the product.

Large decals & windshield banners

Use a helper for large pieces. Measure your glass before removing the backing, and follow the banner’s trim-to-fit notes. Keep visibility, sensors and seals clear. Local rules may limit placement. Have a professional trim the banner if you are not confident doing it safely; never cut into paint, seals or the glass.

Dry application is the default for our small transfer-tape decals. Wet application is only suitable for compatible vinyl on smooth, non-porous glass or vehicle surfaces. Contact us first for your particular product and use a suitable vinyl application fluid. Squeegee out the fluid thoroughly, allow it to dry, then remove the tape. Do not use the wet method on removable wall decals or electronics.

Removable indoor decals, including the mouse kit

Use the dry method on a clean, smooth indoor surface. Test an inconspicuous area first, especially on paint. Follow the paint manufacturer’s curing time, and avoid fragile, peeling, textured or freshly painted finishes. Do not use alcohol on a wall or finish unless its manufacturer permits it.

To remove, warm the vinyl gently with a hair dryer and peel it slowly back on itself. Keep the dryer moving and avoid overheating the surface. Removable vinyl is not a guarantee against damage to weak paint or delicate finishes.

The vinyl stays on the backing, or lifts with the tape

Lay the layers back together and press firmly over the problem area. Peel the paper backing back on itself slowly. If the vinyl lifts from the surface when you remove the transfer tape, stop and re-press it through the tape, wait a little longer, and retry at a low angle.

Ready for your next design?

Choose a size that fits the space you measured.

Shop decals